[China Aluminum Network] The doors and windows in our homes should be used more frequently, and it is also a relatively vulnerable part of many homes. However, if the owner can skillfully perform doors and windows and use and maintenance in peacetime, it can extend the use of doors and windows. Then, let Xiaobian introduce to you the use and maintenance of several different materials doors and windows tips!
Aluminum alloy doors and windows
1. Aluminum alloy doors and windows in the usual use, the action should be light, push and pull along the way; if you find it difficult to hard pull hard push, you should first rule out the existence of the fault. Accumulation of dust, deformation is the main reason for the aluminum alloy doors and windows to push and pull difficult, to keep the door frame clean, in particular to maintain the cleanliness of the door and window sliding slot. A vacuum cleaner can be used to suck away large amounts of dust in the tank and inside the door seal.
2. When aluminum alloy doors and windows are cleaned, people should try not to step on the aluminum frame, and do not use the frame as a support.
3. Aluminum alloy doors and windows can choose to use a soft cloth dipped in water or a neutral detergent, do not use ordinary soap and detergent, but can not use detergent, toilet detergent and other strong acid and alkali cleaners.
4. After the rainy weather, wipe the wet glass and door frames, and pay special attention to drain the water in the chute. If the chute is used for a long time, the friction force is increased. Add a little oil or a layer of wax oil.
5. The joints of the aluminum alloy frame should be inspected frequently and the bolts should be tightened in time to replace the damaged parts. Positioning pins, wind braces, floor springs and other vulnerable parts of aluminum alloy doors and windows, should be checked from time to time, regularly add oil to keep clean and flexible.
6. The seal tops and glass seals are the key structures that ensure the insulation of the doors and windows. If any, they must be repaired and replaced in time.
7. Always inspect the joints of the aluminum alloy frame wall. If the loosening occurs for a long time, the entire frame can easily be deformed, so that the doors and windows cannot be closed and sealed. Therefore, loosening of the screws at the joints should be fastened immediately, such as loosening of the screw footings, and application of epoxy glue to adjust a small amount of cement.
Steel doors and windows
Plastic doors and windows have the same comprehensive performance as aluminum alloy doors and windows, and their maintenance requirements are the same as aluminum alloy doors and windows. However, steel doors and windows are resistant to acid and alkali, and can be cleaned with ordinary detergents such as soap and water, but the surface of plastic doors and windows is not rubbed and rubbed, and special attention should be paid to avoiding scratches. Also be protected from boiling water and high temperature deformation. During the use and cleaning process, the bottom frame of the doors and windows should not be stepped on and hit with hard objects such as knives and hammers.
In addition to routine maintenance after installation, Xiaobian reminds everyone that the inspection after installation is also necessary. Generally, the following five aspects need to be checked after installation of windows and doors:
1. Cracks in the profile welds of doors, windows, and fans.
2. Whether there is obvious deformation, warping, or sagging fans.
3. Check whether the sealing strip and the strip have contraction, deformation, and voids.
4. Whether the hardware accessories are broken, damaged or tight.
5. Whether the drainage hole is open.
Wooden window
1. When cleaning the glass, frame, doors and windows, use clean water or a neutral detergent and wipe with a soft cloth to ensure that the glass, frame, and other parts are not scratched. Every three months, clean the grooves and the slide rails at the joints of the sashes to prevent dust, sand and stones from adversely affecting the normal use of the hardware, and use a fur or vacuum cleaner for cleaning.
2. Check the metal fasteners at the corners of the doors and windows every three months and find that the screws are loose or loose and should be fastened or replaced.
3. Lubricant can be used every six months to lubricate the parts of hardware such as rotation, sliding and lock points. It can be repeatedly opened and closed 3-5 times after dripping into the lubricant to ensure that the lubricating oil is completely adhered and the flexibility of the hardware turning mechanism can be increased. Service life.
4. Do not disassemble doors and windows and accessories on your own or change the structure of windows and doors and the format of the grid. If necessary, contact the manufacturer of the windows and doors or ask a professional to solve the problem on site.
Star Light,Star Light Car,Star Light Ceiling,Galaxy Star Light Projector,Hanging Star Light
Yuyao Flylit Appliance Co.,Ltd , https://www.flylitlight.com