Epoxy self-leveling construction process and precautions are too full!

Epoxy self-leveling performance is impeccable, but due to the construction technology and the quality of the coating itself, the quality difference of the self-leveling floor is also very significant. The following three aspects call everyone to introduce the quality of epoxy self-leveling. The following small series introduces the relevant knowledge of epoxy self-leveling construction process and precautions.

Epoxy self-leveling construction process:

1. Basic inspection and processing

1.1 Anti-static epoxy self-leveling ground has higher requirements on the strength of the base layer, and the strength level of the base layer should not be lower than C20. The original design of the original drawing is 100mm thick and is C20 fine stone concrete, taking into account that most floors are workshops and warehouses, and load-bearing machinery. To pass, it is necessary to reinforce the ground floor of a storey. Through consultation with the Design Institute, a 50mm thick reinforced concrete cushion with strength of C30 is added to the original design base.

1.2 The surface of the bedding requires very high cleaning. The upper layer of concrete is firmly bonded to the underlying cushion, and the surface is required to be hard and smooth. There must be no delamination or sanding.

1.3 The degree of dryness at the base level is due to the large amount of moisture contained in the construction process of the concrete and mortar. It must be dried to the required degree when the ground coating is applied. Water content of concrete can be measured by plastic film method. Plastic film method: Place a 45cm×45cm plastic film on the surface of concrete and seal the four sides with tape for 16 hours. The water droplets appear on the surface of the film or the surface of the concrete turns black, indicating that the concrete is too wet. Not suitable for painting.

1.4 Check the flatness of the floor with a 2m ruler, fill the concave area with an epoxy mortar and compact it, and use a dustless grinder to polish the protruding part to a flat surface.

1.5 The original reserved ground expansion joints shall be filled with PU material or other foaming materials and filled to a depth of 1 to 2mm from the ground.

2. Primer construction

2.1 Use Epoxy Epoxy Primer: The main paint and curing agent are mixed according to the proportion, and stir evenly; with a roller evenly roll, no leakage; door edge, corner, wall foot, machine feet, etc. Use the brush to brush: Roll When coating, be thin and even. After coating, it should be glossy. Matte areas should be painted at the appropriate time.

2.2 Grounding copper mesh: Lay copper foil and conductive system network according to the design requirements, and use plastic putty to fill in the joints.

3. The middle coating construction

Scratch anti-static special coating: After the copper foil is laid, apply the anti-static coating in a scraper to cover the copper foil. After the intermediate coating is completely dried, grind it with the sander and sandpaper, and the knife marks will be generated. The granules are polished away and vacuumed to clean them.

4. Top coat construction

After thoroughly mixing the topcoat and curing agent, apply a special serrated knife to keep the floor flat.

5. Finished product protection

During the hardening of the back layer of the construction (within 24 hours), personnel are forbidden to enter so as not to leave traces. After 7 days of maintenance, it can be used formally. And the surface of the surface is smooth, free of impurities and traces of joints. After the construction, no abnormal phenomena such as air bubbles, poor hardening, and color difference are allowed on the surface.

Epoxy self-leveling construction notes:

1. Construction during the rainy season: If the air humidity exceeds the construction conditions, manual ventilation facilities (exhaust fans, etc.) should be added to control the humidity. Heavy rain, high humidity and other days should stop construction.

2. When the resin is applied to the entire surface, the ambient temperature must not be too low or too high, and the humidity must not be too high to prevent the resin mortar from being sham-cured.

3. The construction site should pay attention to good ventilation.

4. Do not touch the skin during construction. It is best to have protective gloves on both hands.

5. Cleaning site should be cleaned during construction, and site and garbage should be cleared after construction.

6. Dust on the floor must be completely removed to ensure the primer effect.

7. When the ground is wet, it must be dried to a moisture content of 8% or less, or use a special primer.

8. If the layers of epoxy resin are out of the effective ground, the surface of the material must be roughened and treated with a layer of primer (depending on the length of interval) before applying the upper layer of paint.

9. The primer must be fully volatilized before construction can be done to avoid blistering.

10. When preparing the material, the bottom cloth (or cardboard) shall be placed on the bottom half to avoid any single drop of material on the plain, causing quit. If it has been dripped on the plain, it shall be wiped off immediately.

11. The mixed material should be coated within the usable time to avoid surface hardening and failure to level.

12. Immediately remove any sand or other impurities found on the coating.

13. Epoxy resin dustproof and wear-resistant floor construction should pay attention to the mixing ratio, mixing and mixing can be used.

The above is related to the introduction of the epoxy self-leveling construction process and precautions. If you want to know more relevant information, please pay more attention to this site and will provide you with more complete, more detailed and updated information.
 

House Decoration Precautions Construction Installation Home Decoration Precautions Decoration Precautions House Decoration Precautions

Passenger Conveyor Spare Parts

  1. OTIS Passenger Conveyor Spare Parts,
  2. Thyssen Passenger Conveyor Spare Parts,
  3. KONE Passenger Conveyor Spare Parts,
  4. Giant KONE Passenger Conveyor Spare Parts,
  5. ThyssenKrupp Passenger Conveyor Spare Parts,
  6. Schindler Passenger Conveyor Spare Parts,
  7. XJ Schindler Passenger Conveyor Spare Parts,
  8. Xizi OTIS Passenger Conveyor Spare Parts,
  9. Mitsubishi Passenger Conveyor Spare Parts,
  10. Shanghai Mitsubishi Passenger Conveyor Spare Parts,
  11. Fujitec Passenger Conveyor Spare Parts,
  12. Hitachi Passenger Conveyor Spare Parts,
  13. Toshiba Passenger Conveyor Spare Parts,
  14. Hyundai Passenger Conveyor Spare Parts,
  15. LG Passenger Conveyor Spare Parts,
  16. Sigma Passenger Conveyor Spare Parts,
  17. Express Passenger Conveyor Spare Parts,
  18. FUJI Passenger Conveyor Spare Parts,
  19. BLT Passenger Conveyor Spare Parts,
  20. KOYO Passenger Conveyor Spare Parts
  21. SJEC Passenger Conveyor Spare Parts
  22. Canny Passenger Conveyor Spare Parts
  23. IFE Passenger Conveyor Spare Parts

  • OTIS Travellator Spare Parts,

  • Thyssen Travellator Spare Parts,

  • KONE Travellator Spare Parts,

  • Giant KONE Travellator Spare Parts,

  • ThyssenKrupp Travellator Spare Parts,

  • Schindler Travellator Spare Parts,

  • XJ Schindler Travellator Spare Parts,

  • Xizi OTIS Travellator Spare Parts,

  • Mitsubishi Travellator Spare Parts,

  • Shanghai Mitsubishi Travellator Spare Parts,

  • Fujitec Travellator Spare Parts,

  • Hitachi Travellator Spare Parts,

  • Toshiba Travellator Spare Parts,

  • Hyundai Travellator Spare Parts,

  • LG Travellator Spare Parts,

  • Sigma Travellator Spare Parts,

  • Express Travellator Spare Parts,

  • FUJI Travellator Spare Parts,

  • BLT Travellator Spare Parts,

  • KOYO Travellator Spare Parts

  • SJEC Travellator Spare Parts

  • Canny Travellator Spare Parts

  • IFE Travellator Spare Parts

  • OTIS Moving Walk Spare Parts,

  • Thyssen Moving Walk Spare Parts,

  • KONE Moving Walk Spare Parts,

  • Giant KONE Moving Walk Spare Parts,

  • ThyssenKrupp Moving Walk Spare Parts,

  • Schindler Moving Walk Spare Parts,

  • XJ Schindler Moving Walk Spare Parts,

  • Xizi OTIS Moving Walk Spare Parts,

  • Mitsubishi Moving Walk Spare Parts,

  • Shanghai Mitsubishi Moving Walk Spare Parts,

  • Fujitec Moving Walk Spare Parts,

  • Hitachi Moving Walk Spare Parts,

  • Toshiba Moving Walk Spare Parts,

  • Hyundai Moving Walk Spare Parts,

  • LG Moving Walk Spare Parts,

  • Sigma Moving Walk Spare Parts,

  • Express Moving Walk Spare Parts,

  • FUJI Moving Walk Spare Parts,

  • BLT Moving Walk Spare Parts,

  • KOYO Moving Walk Spare Parts

  • SJEC Moving Walk Spare Parts

  • Canny Moving Walk Spare Parts

  • IFE Moving Walk Spare Parts

  • OTIS Moving Sidewalk Spare Parts,

  • Thyssen Moving Sidewalk Spare Parts,

  • KONE Moving Sidewalk Spare Parts,

  • Giant KONE Moving Sidewalk Spare Parts,

  • ThyssenKrupp Moving Sidewalk Spare Parts,

  • Schindler Moving Sidewalk Spare Parts,

  • XJ Schindler Moving Sidewalk Spare Parts,

  • Xizi OTIS Moving Sidewalk Spare Parts,

  • Mitsubishi Moving Sidewalk Spare Parts,

  • Shanghai Mitsubishi Moving Sidewalk Spare Parts,

  • Fujitec Moving Sidewalk Spare Parts,

  • Hitachi Moving Sidewalk Spare Parts,

  • Toshiba Moving Sidewalk Spare Parts,

  • Hyundai Moving Sidewalk Spare Parts,

  • LG Moving Sidewalk Spare Parts,

  • Sigma Moving Sidewalk Spare Parts,

  • Express Moving Sidewalk Spare Parts,

  • FUJI Moving Sidewalk Spare Parts,

  • BLT Moving Sidewalk Spare Parts,

  • KOYO Moving Sidewalk Spare Parts

  • SJEC Moving Sidewalk Spare Parts

  • Canny Moving Sidewalk Spare Parts

  • IFE Moving Sidewalk Spare Parts

  • OTIS Moving Pavement Spare Parts,

  • Thyssen Moving Pavement Spare Parts,

  • KONE Moving Pavement Spare Parts,

  • Giant KONE Moving Pavement Spare Parts,

  • ThyssenKrupp Moving Pavement Spare Parts,

  • Schindler Moving Pavement Spare Parts,

  • XJ Schindler Moving Pavement Spare Parts,

  • Xizi OTIS Moving Pavement Spare Parts,

  • Mitsubishi Moving Pavement Spare Parts,

  • Shanghai Mitsubishi Moving Pavement Spare Parts,

  • Fujitec Moving Pavement Spare Parts,

  • Hitachi Moving Pavement Spare Parts,

  • Toshiba Moving Pavement Spare Parts,

  • Hyundai Moving Pavement Spare Parts,

  • LG Moving Pavement Spare Parts,

  • Sigma Moving Pavement Spare Parts,

  • Express Moving Pavement Spare Parts,

  • FUJI Moving Pavement Spare Parts,

  • BLT Moving Pavement Spare Parts,

  • KOYO Moving Pavement Spare Parts

  • SJEC Moving Pavement Spare Parts

  • Canny Moving Pavement Spare Parts

  • IFE Moving Pavement Spare Parts

  • OTIS Autowalk Spare Parts,

  • Thyssen Autowalk Spare Parts,

  • KONE Autowalk Spare Parts,

  • Giant KONE Autowalk Spare Parts,

  • ThyssenKrupp Autowalk Spare Parts,

  • Schindler Autowalk Spare Parts,

  • XJ Schindler Autowalk Spare Parts,

  • Xizi OTIS Autowalk Spare Parts,

  • Mitsubishi Autowalk Spare Parts,

  • Shanghai Mitsubishi Autowalk Spare Parts,

  • Fujitec Autowalk Spare Parts,

  • Hitachi Autowalk Spare Parts,

  • Toshiba Autowalk Spare Parts,

  • Hyundai Autowalk Spare Parts,

  • LG Autowalk Spare Parts,

  • Sigma Autowalk Spare Parts,

  • Express Autowalk Spare Parts,

  • FUJI Autowalk Spare Parts,

  • BLT Autowalk Spare Parts,

  • KOYO Autowalk Spare Parts

  • SJEC Autowalk Spare Parts

  • Canny Autowalk Spare Parts

  • IFE Autowalk Spare Parts








Autowalk Spare Parts,Travelator Spare Parts,Moving Walk Spare Parts,Moving Sidewalk Spare Parts

CEP Elevator Products ( China ) Co., Ltd. , https://www.zjfullelevatorreplacement.com