1. Every time before starting, routinely check the surrounding environment, fastening bolts, oil leakage, and the integrity of the cable. It should create conditions for normal operation.
2. Every time you start, you should start with jog and gradually turn into normal. After running for 10 minutes, check the vibration, noise, and temperature rise of each running part.
3. If the electric drum is leaking oil, pay attention to check the two parts: First, the oil seal, whether it is worn or deformed, the wear can tighten the spring ring of the oil seal lip part, and the oil seal of the wear quantity book is large. Can solve the leak. If it is invalid or deformed, the skeleton oil seal should be replaced in time; secondly, the outlet passage cannot be blocked, and the deposited dust, oil and debris should be removed as soon as possible to ensure the smooth passage.
4. The replacement of the cooling oil, the first oil change time is 10 days, the second time is 1 month, and the oil is changed every three months thereafter. For parts filled with grease, such as motor bearings for the outer packaging drum and the output shaft support of the cycloidal drum, always pay attention to the filling. Generally, it is added once a month, and the new oil is refilled every six months.
5. The backstop used for the high-speed shaft of the outer drum is generally cooled and lubricated by the cooling oil inside the cylinder through the built-in passage to the backstop. To prevent the shortage of oil supply, add the top of the backstop. When the pressure-filling oil cup is installed, when the temperature rises quickly, the oil should be replenished from the oil cup for replenishment. The number of oil injections should not be too much. It should be three to four times a month, and each time the oil filling book exceeds 150. Gram. The backstop should be able to act as a backstop, otherwise the backstop will be damaged.
6, the drum if there is no special circumstances, generally do not need maintenance, but should be carried out for normal maintenance. It can be cleaned once every six months. It is not necessary to remove the gears inside the cleaning cylinder, (cycloid or planetary gear) and the supporting and running parts, and replace the cooling lubricant. Maintenance once a year, disassemble the support, end cover, cylinder, cleaning the inner wall of the cylinder and the transmission body, check the wear of the gears, cycloidal wheel and bearing. Check the force part, whether the key or keyway is deformed, whether the oil seal is worn or not. Great maintenance every two years, disassemble all parts, inspect, repair or replace. All oils used in oil-immersed electric drums should be used strictly in accordance with the specified oil types in the instruction manual. Users should not arbitrarily change the oil types to prevent the motor from burning out.
7. Regularly checking the oil level in the drum is an important part of daily maintenance. The specified oil level is one of the conditions to ensure the normal operation of the drum. The inspection method can be checked according to the method described in the instruction manual. For the adjustment and maintenance of the electric hydraulic block brake and the maintenance of the fluid coupling, please follow the instruction manual of the product.
Concerned about surprises
Label: Daily maintenance and maintenance of electric drum
Previous: Solenoid valve manufacturers six working principles cheats to get the daily dimension Next: Oil temperature machine common fault analysis and elimination
Sealand is a trustworthy manufacturer of Gas Mass Flow Meter, Gas Mass Flowmeter, Gas Flow Meter, Gas Flowmeter, Gas Meter, ATEX, IECEx & CE approved.
The installation is as follows.
1. Installation Steps
a) Choose correct installation site, taking installation area, pipeline, transmitter location &
valve location into consideration;
b) Install the meter according to direction mark on sensor;
c) Install the sensor & transmitter on pipeline;
d) Connect transmitter & sensor with 9-pin cable;
e) Start.
a) Sensor stays away from mechanical vibration source, for example, pump. Use flexible pipe to connect meter with pipeline if inevitable. The housing of meter must be standalone, out of touch with any other device. There must be 3 times the size of sensor between 2 sensors if there are many flow meters on the same pipeline, to avoid resonance.
b) Do not install sensor on pipeline that easily expands with hot and contracts with cold, especially near expansion joint, which leads to a worse stability.
c) Sensor stays away from industrial electromagnetic field, such as large generator and transformer, better 5m at least. Such device influences the performance of drive coil and pickoffs. Make sure magnetic field intensity less than 400A/m.
d) Sensor shall be installed on lower pipeline, to be easily full of fluid.
e) Make sure Ex-mark meet application requirements if in hazardous area.
f) Build a sunshade if the meter is under direct solar radiation. g) Keep the meter from corrosive liquid.
Gas Mass Flow Meter, Gas Mass Flowmeter, Gas Flow Meter, Gas Flowmeter, Gas Meter
Zhejiang Sealand Technology Co., Ltd. , https://www.sealandflowmeters.com