When decorating the house, the waterproof must be done well, otherwise it will bring us a lot of trouble, especially the waterproofing of the toilet is especially important. Next, the decoration house is small, it will be for everyone. Let me introduce the waterproof wall of the toilet . Let's first understand what the waterproof method of the toilet wall is, and then look at the precautions for waterproofing the toilet.
First, the toilet wall waterproofing method introduction
1. The ground can be found in the direction of the floor drain, cement mortar or bean stone concrete, but the surface should be flat. The slope near the door is small, and the slope near the floor drain is large, and it is mastered according to the specific situation. The pipeline penetrates the root of the slab to enhance waterproofing. The tube root building sealant is tightly sealed. After the cement is smoothed and the foot is protected, the waterproof layer of the glass cloth is reinforced with 1~2 layers of the glass cloth reinforcement layer. The same measures are near the floor drain.
2, the wall surface is clean and flat, no floating ash, small particles, and the surface of the wall is wiped with a small original angle or a slope angle. When brushing the waterproof coating, stick the reinforced layer of glass cloth to 1~2 layers. The total thickness of the polyurethane waterproof coating film is required to be 1.5 mm or more. Can not be determined by the number of passes. The tube root and the corner reinforcement layer are first brushed, and after drying at room temperature for 4 hours, a large area is painted and scraped. There must be no slipping or bubbling. Apply a large area after 24 hours of curing and then apply the next layer.
3. Brush the plane after painting the façade first, and the brushing direction of the next pass is perpendicular to the previous one. When the film is semi-cured for the last time, the coarse sand is thrown to facilitate the later bonding with the cement mortar. The ground waterproof layer should be painted 300 feet away from the bathroom door. The waterproof floor waterproof layer should be higher than the ground 200. The bathroom wall waterproof layer with shower should be higher than the ground 1800 (L8 is recommended to be waterproof on the wall).
Second, the toilet waterproofing precautions
1. Do a leveling. First, use cement mortar to level the floor (especially the house that has been refurbished) and then do waterproofing. This can prevent the waterproof coating from leaking due to uneven thickness or piercing the waterproof membrane.
2, to do a good job. The seam between the wall and the ground and the joint between the upper and lower water pipes and the ground are the most prone to problems. Therefore, these parts must be paid special attention, the treatment must be meticulous, and there must be no sloppy.
3, the wall must also be waterproof. In order to achieve a better waterproof effect, the wall surface of the general bathroom should also be waterproofed to a height of about 30 cm to prevent water from escaping through the wall. The wall adjacent to the bathtub is also water-treated to a height higher than the upper edge of the bathtub, and the shower must be 180 cm high.
4, to do waterproof experiments. After the waterproof construction is completed, all the sewers in the toilet should be blocked and the water injection test should be carried out. Check after 24 hours, if there is no leakage around the wall and floor of the bathroom, the waterproof quality of the bathroom is very good. On the contrary, find out the missing points and carry out maintenance.
5. Closed water test. In the closed water test, the water at the highest point on the ground shall not be less than 2 cm, and it shall be stored for at least 24 hours, and it shall be qualified after observing no leakage. If there is leakage, you need to redo it, and you should not neglect it.
Xiaobian hopes that friends must read it carefully. Xiaobian introduces to everyone, the toilet wall waterproofing method and the toilet waterproofing are all different, I hope that the introduction of Xiaobian can help the parents, if still Want to know, more home improvement information, please continue to pay attention to, decoration home network.
More related wonderful reading:
Bathroom wall waterproofing practice bathroom waterproofing skills
Bathroom wall waterproof coating type bathroom wall waterproof coating
What kind of brand of wall waterproofing material? Waterproof material purchase tips
Bathroom wall waterproof material price bathroom waterproof precautions
How to make waterproof treatment of indoor wall? Wall waterproofing method
Privacy Dimming Glass costs more than Smart Film because it includes the glass and involves a lamination and cutting process. However, when installation is factored in it is not always the less expensive option. For example, if a new home is being built and glass will need to be ordered and installed anyways then ordering smart glass would not incur any additional costs other than the cost of product. If one were to order new glass and have it installed and then order smart film and have it installed it could incur an additional installation cost.
Through carefully layering, switchable designs and logos can be embedded within Magic Film For Glass. These designs disappear and appear within the glass, seamlessly transitioning between 4 different states. This gives companies a further opportunity to make an impact and is a great option for branding commercial windows, reception areas and boardrooms.
With smart glass technology, you can create a sleek modern look that is unaffected by the movement of the sliding door, unlike curtains and blinds.
Electrochromic Switchable Smart Tint Film,Smart Glass,Smart Film For Hologram Projector,Smart Window Tint Glass,Smart Home Glass Door
Tianqixun Technology , https://www.tqxdisplay.com