The basin faucet is a sanitary ware that is indispensable for the kitchen and the bathroom. If the basin faucet is clogged or damaged, it will also cause a normal daily life "clogging." In order to solve the problem of life jam, we need to remove the basin faucet to check the fault, then the problem came: How to remove the basin faucet ? Do you need to pay attention to the removal of the lavatory faucet? Next Xiaobian will introduce the steps of how to remove the basin faucet .
First, under what circumstances need to remove the basin faucet?
Congestion, water leakage, and the inability to store water are the most common problems with basin faucets. Problems with omissions and improper installation can cause problems. When a household faucet has the following “symptoms,†it is necessary to consider removing the faucet and performing repairs. :
1. Some consumers found that when used, consumers used a plug in the basin to plug the tub into the mouth of the hose, and there was no water in the basin. This is because when the basin faucet is installed, the contact part of the falling water basin is not sealed and needs to be removed and sealed;
2. After closing the lavatory faucet, the water at the outlet is still flowing, which cannot be stopped at all. This is usually a problem with the inlet valve spool. Garbage plugs the sealing ring at the bottom of the valve plug, the sealing ring is damaged, or it is in the pipeline. Impurities scratching the spool can cause this.
Second, how to split the basin faucet
The basin faucet is connected to the angle valve by means of a water inlet hose, and is fastened to the face of the basin basin by a fastening nut. When disassembling, it mainly starts from these two aspects:
1. Before you start to remove the basin faucet, find the inlet valve. The inlet valve is usually mounted on the wall below the basin. First screw on the angle valve to cut off the water, otherwise there will be a lot of flowing water wasted during the removal of the basin faucet;
2. After screwing on the angle valve, some water will remain in the water pipe, and the tap will be opened to discharge the remaining water.
3. When the basin faucet is installed, connect the water inlet port of the basin faucet with the angle valve with the water inlet hose. Hold the water pipe with one hand when disassembling, twist the wrench with one hand, and remove the end of the water inlet hose connecting the basin faucet;
4, when the basin faucet is installed, after connecting the water hose, it needs to be fastened; the nut will lock it, so after removing the water inlet hose, find the fastener of the basin faucet and unscrew it with a pliers or a wrench. Remove the basin faucet.
Three, basin faucet removal notes
1. The hoses under some household basin taps are deep inside the pipe and the disassembly takes some effort. This is because during installation, the plug seat may be screwed onto the faucet body. You can use a relatively long screwdriver to turn the screw counterclockwise from below, and then from the bottom up to the top of the spool seat and high-pressure hose, pay attention to the top, to avoid damage to the seal seat on the seat and then remove hose;
2. Some water inlet hoses are used for a long time. Embrittlement or rusting of the fasteners may cause the water inlet hose to be unscrewed. After dripping two or three drops of oil on the rusted part, remove the basin faucet.
Conclusion: After use in peacetime, you need to clean the basin connection in a timely manner to avoid sharp objects flowing into the inlet pipe, so that you can use more durable! The above instructions on how to remove the basin faucet and the demolition of the basin faucet are briefly introduced here. I hope to help you. For more information, please visit this website. Stay tuned.
Basin bathroom sink faucet
High Speed self-Recovery Rapid doors are the technological evolution of old, PVC high speed doors or heavy folding doors, now obsolete and not suited to today's industrial needs.
High-quality panels, the resistive safety edge fitted to the bottom edge of the door, photocells and barriers make this product both safe and durable, being totally self-repairing, thanks to its special [Anti Crash System".
This door designed with a perimeter structure in galvanized or stainless steel, which is ideal for sliding panels. The door panel rides effortlessly within a track, thanks to the special profile and hinge designed by us, requiring low maintenance. The panel is rolled up on a roller placed within the upper crossbeam.
The door can be equipped with a counterweight or ups batteries, to fully open the door in case of power failure, and can also be equipped with large transparent sections to create a brighter and safer working environment.
Self-Repairing Door Curtain made of reinforced PVC, with flexible weighted soft bottom edge.
The edge of curtain has continuous injection molded teeth that then move up and down in a self-lubricating polyethylene track attached to structural galvanized side frames.
Self-Recovery Rapid Door,Self Recovery PVC Rapid Door,Self Recovery Rapid Rolling Door,Self Healing Roll Door
Shenzhen Hongfa Automatic Door Co., Ltd. , https://www.hfautodoors.com