1. Question: What is the cause of the jitter in the monitor display?
answer:
This situation is generally caused by the display refresh rate setting is too low, enter the "Display Properties" click "Settings", select "Advanced", then select "Monitor", the new frequency is adjusted to 75HZ, after the exit can be resolved This problem.
2. Question: Why does the monitor appear as a screen saver or a black screen after the monitor is turned on for a while?
answer:
This situation is caused by not having to cancel the screen saver or improper power management settings. The solution is to exit from the monitoring system to the WINDOWS operating system interface, right-click on the interface, select "Properties", select the screen saver in the tab appears, select (none) to cancel the screen saver. Then click on the settings button in the lower right corner, select "Always open" in the power scheme, the system waits to select "never", close the monitor and select "never", "close the hard disk" where "never", and finally click "OK" can be.
3. Question: What is the reason why the digital hard disk recorder image shows only the image without the operation button or the screen is not full of the entire screen?
answer:
Under normal circumstances, the display resolution setting does not meet the requirements, the desktop resolution is set to 1024*768, and the small font can be changed to a large font.
4. Question: How should the HD video host be partitioned?
answer:
System main hard disk:
1) Create primary partition C: (2 to 3GB) (OS + application software.)
2) Create an extended partition (100% of the remaining hard disk)
3) create a logical partition in the extended partition D: (usually allocated about 4GB, mainly stored application backup and some video data)
4) Create logical partition E under the extended partition: (remaining hard disk space) (video data)
The system expands the hard disk: Each partition is divided into only one extended partition, and only one logical partition is established under the extended partition.
Special attention: The host hard disk must be divided into at least C: D: E: more than three partitions, otherwise the system does not work.
5. Question: What can I do if I get stuck after I can't loop video or video is full?
answer:
First of all, read the instructions of the host computer carefully to confirm whether the video recording mode is set to “one record†or “recycle videoâ€. Second, this situation is very likely related to the tools used by the hard disk partition. It is recommended not to use any hard disk partitioning tools. WINDOWS98 is best used to partition using the FDISK partition command. WINDOWS 2000 uses its own partitioning tool for partitioning.
Why does the image display have no operation buttons, only images?
Set the desktop resolution to 1024*768, then click Advanced in this tab, then change the small font to large.
6. Why does the monitor appear with a screen saver or a black screen when the monitor is turned on for a while?
After exiting to the operating system interface, right-click on the interface, select Properties, select Screen Saver in the tab that appears, and select (none) to deactivate the screen saver. Then click on the settings button in the lower right corner, select "Always open" in the power scheme, the system waits to select "never", close the monitor and select "never", close the hard disk and select "never" and then OK.
7, why no boot?
Make sure the chassis and monitor are properly connected and the power is connected and turned on. In the process of transportation and moving, the body may loosen the internal card accessories. It is best to open the chassis before starting the machine and confirm that the components are plugged in and then turned on. If the main board self-test is abnormal during startup (normally, the keyboard indicator LED flashes once and the host buzzer emits a “beep†sound), please turn off the power and check whether the CPU board and video card are fully inserted and remove the board. Plug in again. If you press the power switch and the CPU fan does not turn and the panel power indicator does not light, check that the power supply is connected properly.
8. Why does the system crash? How to restore?
If the improper setting of windows or some other software failure causes the system to work abnormally, system crashes will occur. The following methods can be used to recover the system:
First: Windows registry method repair system. For example, if you do not open the monitor or the monitor is connected improperly when you start the system for a certain time, the system cannot be normally accessed when the system restarts. You can use the following steps to repair it.
Restart, hold down the F8 key during startup, select "Command Prompt only" in the boot mode selection menu, and after booting, type the following command line: scanreg /restore Select the date of the most recent system work to restore.
Second: When using the recovery registry can not solve the problem, you can use Ghost to restore the system, provided that you have used the Ghost backup system. Use method is to start (start with the hard disk or start the boot disk WIN98) to DOS state, run Ghost.exe, follow the prompts to complete the system recovery.
9. What should I do if there is no image display?
One reason: Due to incompatibility of the graphics card, the Direct Draw test can be used. If the test passes, this is not the reason.
Cause two: The PCI interface is not in good contact. You can switch to a PCI slot test.
Cause three: If the card is damaged, you can consider changing the card test.
10. Audio and video card driver installation instructions.
The driver for the video card cannot be installed in more than one. Only check the complete number of drivers in safe mode.
Example: You have 8 cards plugged into the motherboard. You can only install 8 drivers. You should check the number of audio and video card drivers in "Safe Mode". If the video card driver is more than the number of installed video cards, the system sometimes does not work properly.
Note: Four-way real-time cards are equivalent to four independent cards, four drivers need to be installed, and the other audio and video cards install one driver for each card! If you find this phenomenon, you should put all video cards in "safe mode". Remove all the drivers (including other duplicate devices of the system), and then restart the computer.
11. Why can't the computer find the card?
Cause one: The computer power supply is not ATX power supply. Please use ATX power supply.
Cause two: The computer's PCI slot is damaged. Please change it to a slot test.
Cause 3: The card is damaged. Please change the card test.
12. What should I do if the video playback quality is poor?
For our hard disk video recorder under the "normal" compression quality, video playback quality is satisfactory. But sometimes the “mosaic†phenomenon is serious, especially for moving images, the image becomes blurred. The main reason is that your camera's brightness is too low (do not try to change the brightness of the hard disk recorder to compensate), you have to re Adjust the brightness of the camera to compensate. This should pay special attention to the construction of the project.
13. What if the real-time monitoring image is not clear?
In the system setting of the digital hard disk recorder, "common camera" or "high definition camera" can be selected according to the model or the resolution of the configured camera; at the same time, the brightness, chroma, contrast and saturation of the video can also be adjusted. Value to achieve satisfactory results.
14, the program can not start or initialization failed how to do?
Cause one: The shortcut is wrong. Unable to hook the application, the shortcut does not start, delete the shortcut and recreate or reinstall the program.
Reason two: There is no installation of DirectX 8.0 or later acceleration software.
Cause 3: The card model has not been correctly identified. Run the Config.exe program to identify the card.
Cause four: The power supply is not ATX power supply or the power supply power is not enough. Switch to a high-power ATX power supply.
Cause five: The board is in poor contact and reinstall the board.
Cause six: The software and card are not compatible, that is, they are not compatible. Contact the product supplier.
Cause seven: There is a bad card and you need to confirm the availability of each card.
Cause 8: The PCI slot is damaged. Replace the slot.
15. What if the monitor button does not work?
Cause one: No audio is used or the selected channel does not have audio.
Cause two: The sound card is not installed or the sound card driver is not installed.
Cause 3: The sound card is not working properly. We recommend using the Direct Sound test by running the Dxdiag.exe program in the C:WINDOWSSYSTEM directory to test the working status of the sound card. If the test fails, follow the instructions below:
First: Restart the computer to "safe mode", open the device manager, remove all duplicate device drivers, restart the installation of the driver, run the Dxdiag.exe program test, can pass the test. If it still doesn't work, press a step.
Second: If there is a problem with the integrated sound card, during the replacement of the sound card, please shield the integrated sound card in the BIOS, otherwise it cannot be used; for a sound card, run the Dxdiag.exe program test, if you can not pass the test, you can only replace Motherboard.
16, audio monitoring, playback is not normal how to do?
If the audio monitored and played back is not normal, the possible causes are:
Cause one: system compatibility caused.
When using the IPC to install the system, it is recommended that the audio card be installed in the basic PCI slot (* the slot near the CPU board).
Such as: Vectra motherboard, the basic PCI slot name is: PCI X, X is the serial number, PCI expansion name is SPCI X, it is recommended that the audio card is installed in the PCI X slot; EVOC motherboard, the basic PCI name is: PCI1-X, X is the serial number, and the extension PCI name is PCI2-X. It is recommended that the audio card be installed in the PCI1-X slot. Commercial motherboards do not have this problem.
Cause two: The driver of the sound card driver or system device is installed incorrectly.
In secure mode, check the sound card and system device drivers, remove duplicate device drivers, restart the computer, and install the driver provided by the product vendor. And using DirectSound testing, it is best to use a sound card with software buffering and hardware buffering.
Reason 3: Since the sound output amplitude of the monitor on the market is different, the factory setting of our company is: VPP=2V. The mismatch of the audio input's amplitude results in poor audio performance. You can adjust the magnification by inputting the audio/video card. If the monitor's output amplitude is not within the listed range, it can only adjust the monitor's output amplitude, such as: reduce the monitor's power supply voltage.
17. Monitor is normal, but no sound is played back?
The reason is that the "Allow recording" is not set. In the "camera settings" of the system settings, the desired recording camera is checked "Allow recording".
18. Why is the image still?
It may be that the audio and video card is dead. It may be that the audio and video card is not in good contact with the PCI slot of the computer. You can turn off the computer and restart the computer. If there is a more frequent dead card phenomenon, you can consider changing the card; if not very often The situation may be because the system working time is too long, you can set the system to restart at regular intervals to relieve the system working pressure and release the memory; you can also add a reset line connected to the computer on a certain card of the system to achieve automatic recovery. The purpose of the system.
answer:
This situation is generally caused by the display refresh rate setting is too low, enter the "Display Properties" click "Settings", select "Advanced", then select "Monitor", the new frequency is adjusted to 75HZ, after the exit can be resolved This problem.
2. Question: Why does the monitor appear as a screen saver or a black screen after the monitor is turned on for a while?
answer:
This situation is caused by not having to cancel the screen saver or improper power management settings. The solution is to exit from the monitoring system to the WINDOWS operating system interface, right-click on the interface, select "Properties", select the screen saver in the tab appears, select (none) to cancel the screen saver. Then click on the settings button in the lower right corner, select "Always open" in the power scheme, the system waits to select "never", close the monitor and select "never", "close the hard disk" where "never", and finally click "OK" can be.
3. Question: What is the reason why the digital hard disk recorder image shows only the image without the operation button or the screen is not full of the entire screen?
answer:
Under normal circumstances, the display resolution setting does not meet the requirements, the desktop resolution is set to 1024*768, and the small font can be changed to a large font.
4. Question: How should the HD video host be partitioned?
answer:
System main hard disk:
1) Create primary partition C: (2 to 3GB) (OS + application software.)
2) Create an extended partition (100% of the remaining hard disk)
3) create a logical partition in the extended partition D: (usually allocated about 4GB, mainly stored application backup and some video data)
4) Create logical partition E under the extended partition: (remaining hard disk space) (video data)
The system expands the hard disk: Each partition is divided into only one extended partition, and only one logical partition is established under the extended partition.
Special attention: The host hard disk must be divided into at least C: D: E: more than three partitions, otherwise the system does not work.
5. Question: What can I do if I get stuck after I can't loop video or video is full?
answer:
First of all, read the instructions of the host computer carefully to confirm whether the video recording mode is set to “one record†or “recycle videoâ€. Second, this situation is very likely related to the tools used by the hard disk partition. It is recommended not to use any hard disk partitioning tools. WINDOWS98 is best used to partition using the FDISK partition command. WINDOWS 2000 uses its own partitioning tool for partitioning.
Why does the image display have no operation buttons, only images?
Set the desktop resolution to 1024*768, then click Advanced in this tab, then change the small font to large.
6. Why does the monitor appear with a screen saver or a black screen when the monitor is turned on for a while?
After exiting to the operating system interface, right-click on the interface, select Properties, select Screen Saver in the tab that appears, and select (none) to deactivate the screen saver. Then click on the settings button in the lower right corner, select "Always open" in the power scheme, the system waits to select "never", close the monitor and select "never", close the hard disk and select "never" and then OK.
7, why no boot?
Make sure the chassis and monitor are properly connected and the power is connected and turned on. In the process of transportation and moving, the body may loosen the internal card accessories. It is best to open the chassis before starting the machine and confirm that the components are plugged in and then turned on. If the main board self-test is abnormal during startup (normally, the keyboard indicator LED flashes once and the host buzzer emits a “beep†sound), please turn off the power and check whether the CPU board and video card are fully inserted and remove the board. Plug in again. If you press the power switch and the CPU fan does not turn and the panel power indicator does not light, check that the power supply is connected properly.
8. Why does the system crash? How to restore?
If the improper setting of windows or some other software failure causes the system to work abnormally, system crashes will occur. The following methods can be used to recover the system:
First: Windows registry method repair system. For example, if you do not open the monitor or the monitor is connected improperly when you start the system for a certain time, the system cannot be normally accessed when the system restarts. You can use the following steps to repair it.
Restart, hold down the F8 key during startup, select "Command Prompt only" in the boot mode selection menu, and after booting, type the following command line: scanreg /restore Select the date of the most recent system work to restore.
Second: When using the recovery registry can not solve the problem, you can use Ghost to restore the system, provided that you have used the Ghost backup system. Use method is to start (start with the hard disk or start the boot disk WIN98) to DOS state, run Ghost.exe, follow the prompts to complete the system recovery.
9. What should I do if there is no image display?
One reason: Due to incompatibility of the graphics card, the Direct Draw test can be used. If the test passes, this is not the reason.
Cause two: The PCI interface is not in good contact. You can switch to a PCI slot test.
Cause three: If the card is damaged, you can consider changing the card test.
10. Audio and video card driver installation instructions.
The driver for the video card cannot be installed in more than one. Only check the complete number of drivers in safe mode.
Example: You have 8 cards plugged into the motherboard. You can only install 8 drivers. You should check the number of audio and video card drivers in "Safe Mode". If the video card driver is more than the number of installed video cards, the system sometimes does not work properly.
Note: Four-way real-time cards are equivalent to four independent cards, four drivers need to be installed, and the other audio and video cards install one driver for each card! If you find this phenomenon, you should put all video cards in "safe mode". Remove all the drivers (including other duplicate devices of the system), and then restart the computer.
11. Why can't the computer find the card?
Cause one: The computer power supply is not ATX power supply. Please use ATX power supply.
Cause two: The computer's PCI slot is damaged. Please change it to a slot test.
Cause 3: The card is damaged. Please change the card test.
12. What should I do if the video playback quality is poor?
For our hard disk video recorder under the "normal" compression quality, video playback quality is satisfactory. But sometimes the “mosaic†phenomenon is serious, especially for moving images, the image becomes blurred. The main reason is that your camera's brightness is too low (do not try to change the brightness of the hard disk recorder to compensate), you have to re Adjust the brightness of the camera to compensate. This should pay special attention to the construction of the project.
13. What if the real-time monitoring image is not clear?
In the system setting of the digital hard disk recorder, "common camera" or "high definition camera" can be selected according to the model or the resolution of the configured camera; at the same time, the brightness, chroma, contrast and saturation of the video can also be adjusted. Value to achieve satisfactory results.
14, the program can not start or initialization failed how to do?
Cause one: The shortcut is wrong. Unable to hook the application, the shortcut does not start, delete the shortcut and recreate or reinstall the program.
Reason two: There is no installation of DirectX 8.0 or later acceleration software.
Cause 3: The card model has not been correctly identified. Run the Config.exe program to identify the card.
Cause four: The power supply is not ATX power supply or the power supply power is not enough. Switch to a high-power ATX power supply.
Cause five: The board is in poor contact and reinstall the board.
Cause six: The software and card are not compatible, that is, they are not compatible. Contact the product supplier.
Cause seven: There is a bad card and you need to confirm the availability of each card.
Cause 8: The PCI slot is damaged. Replace the slot.
15. What if the monitor button does not work?
Cause one: No audio is used or the selected channel does not have audio.
Cause two: The sound card is not installed or the sound card driver is not installed.
Cause 3: The sound card is not working properly. We recommend using the Direct Sound test by running the Dxdiag.exe program in the C:WINDOWSSYSTEM directory to test the working status of the sound card. If the test fails, follow the instructions below:
First: Restart the computer to "safe mode", open the device manager, remove all duplicate device drivers, restart the installation of the driver, run the Dxdiag.exe program test, can pass the test. If it still doesn't work, press a step.
Second: If there is a problem with the integrated sound card, during the replacement of the sound card, please shield the integrated sound card in the BIOS, otherwise it cannot be used; for a sound card, run the Dxdiag.exe program test, if you can not pass the test, you can only replace Motherboard.
16, audio monitoring, playback is not normal how to do?
If the audio monitored and played back is not normal, the possible causes are:
Cause one: system compatibility caused.
When using the IPC to install the system, it is recommended that the audio card be installed in the basic PCI slot (* the slot near the CPU board).
Such as: Vectra motherboard, the basic PCI slot name is: PCI X, X is the serial number, PCI expansion name is SPCI X, it is recommended that the audio card is installed in the PCI X slot; EVOC motherboard, the basic PCI name is: PCI1-X, X is the serial number, and the extension PCI name is PCI2-X. It is recommended that the audio card be installed in the PCI1-X slot. Commercial motherboards do not have this problem.
Cause two: The driver of the sound card driver or system device is installed incorrectly.
In secure mode, check the sound card and system device drivers, remove duplicate device drivers, restart the computer, and install the driver provided by the product vendor. And using DirectSound testing, it is best to use a sound card with software buffering and hardware buffering.
Reason 3: Since the sound output amplitude of the monitor on the market is different, the factory setting of our company is: VPP=2V. The mismatch of the audio input's amplitude results in poor audio performance. You can adjust the magnification by inputting the audio/video card. If the monitor's output amplitude is not within the listed range, it can only adjust the monitor's output amplitude, such as: reduce the monitor's power supply voltage.
17. Monitor is normal, but no sound is played back?
The reason is that the "Allow recording" is not set. In the "camera settings" of the system settings, the desired recording camera is checked "Allow recording".
18. Why is the image still?
It may be that the audio and video card is dead. It may be that the audio and video card is not in good contact with the PCI slot of the computer. You can turn off the computer and restart the computer. If there is a more frequent dead card phenomenon, you can consider changing the card; if not very often The situation may be because the system working time is too long, you can set the system to restart at regular intervals to relieve the system working pressure and release the memory; you can also add a reset line connected to the computer on a certain card of the system to achieve automatic recovery. The purpose of the system.
Aluminum Windows And Doors,Aluminum Casement Window,Oem Aluminum Casement Windows,Aluminum Sliding Window Frame
Guangdong Jihua Aluminium Co., LTD , https://www.gdaaluminiumprofile.com