Send a process on the putty brush latex paint
Process flow
First, product protection. Mainly the plastic window seams and radiators, to prevent shovel spalling caused by the wall after the garbage is not easy to clean.
Second, spade shovel. You can do a slight water test to check the adhesion of the original coating, carefully observe whether there is a small crack, the vast majority of the walls have been tested on a word: shovel!
Third, the wall closed 801 glue again. The purpose is to enhance the bond between the putty and the wall. If you encounter an old house, you can brush the interface agent to increase the insurance factor.
Fourth, yin and yang processing. After all the yin and yang angles have “elasticatedâ€, use gypsum powder and white latex to adjust the gypsum putty to find straight. Under normal circumstances, plaster line is not recommended.
Fifth, the wall leveling. First check the wall for "empty drum" (knock, listen to the sound judgment), and then use a slightly longer aluminum ruler to check the top and wall depressions, mark, with grit putty.
Six, formally putty. After the plaster putty is dry, putty is applied three times (every pass must be thoroughly dried). There are two methods to test whether the putty is dry: firstly, observe whether the color is consistent; and then see if there is any phenomenon of “sticky sandpaper†when polishing.
Seven, strong light oblique polished. The top surface can be used with No. 360 sandpaper, and the wall surface is best to use 500 or more.
Eight, brush one. After the walls of the floating dust are clean, you can paint the wall paint for the first time (the first pass can be diluted, and the second and third passes are slightly thicker).
Nine, find supplements. Strong light obliquely, looking for compensation and secondary polishing. Looks good on the wall, once brushed over the wall paint, small flaws immediately revealed no doubt, so must be brushed again, after the second seeking repair, polished, in order to have good results.
Ten, brush two. After the inspection, paint the second and third coats of the wall paint.
Note:
First, gypsum powder and 801 must use high quality materials. Like me, I only use "Hongxu" gypsum powder and "Suizhong" 801 rubber and white latex.
Second, fossil powder and putty powder are better or worse? Answer: putty powder. There is a situation that allows oil workers to adjust their own - after the house is decorated, let the special stay for ten years. understand? !
Third, according to the specification, the wall paint should all be brushed three times, two times is very informal.
Four, when calculating the area, do not use too complicated way to convert. Multiplying the building area by two is almost the same. Do not make it too complicated. When looking for oil workers, let special report area, naturally know whether it is real.
Fifth, with the actual painting area, you can calculate the amount of their own. The amount of putty powder per square meter is basically about 2.5 kilograms; the actual brushing area per liter of wall paint is 5-7 square meters. Do not be misled by the sales staff of the store. Specialists calculate the theoretical value (significantly different from the construction value).
Six, putty powder is a general term (including ordinary putty and gypsum putty). And what we usually call putty powder does not include gypsum powder. Gypsum powder is generally used as a local leveling, putty powder is a large area of ​​scraping, but the putty is more than a certain thickness, there may be cracking, so you need to apply a thicker place, only gypsum powder, and gypsum powder must use 801 Or white latex to prepare, putty powder with tap water can be.
Process flow
First, product protection. Mainly the plastic window seams and radiators, to prevent shovel spalling caused by the wall after the garbage is not easy to clean.
Second, spade shovel. You can do a slight water test to check the adhesion of the original coating, carefully observe whether there is a small crack, the vast majority of the walls have been tested on a word: shovel!
Third, the wall closed 801 glue again. The purpose is to enhance the bond between the putty and the wall. If you encounter an old house, you can brush the interface agent to increase the insurance factor.
Fourth, yin and yang processing. After all the yin and yang angles have “elasticatedâ€, use gypsum powder and white latex to adjust the gypsum putty to find straight. Under normal circumstances, plaster line is not recommended.
Fifth, the wall leveling. First check the wall for "empty drum" (knock, listen to the sound judgment), and then use a slightly longer aluminum ruler to check the top and wall depressions, mark, with grit putty.
Six, formally putty. After the plaster putty is dry, putty is applied three times (every pass must be thoroughly dried). There are two methods to test whether the putty is dry: firstly, observe whether the color is consistent; and then see if there is any phenomenon of “sticky sandpaper†when polishing.
Seven, strong light oblique polished. The top surface can be used with No. 360 sandpaper, and the wall surface is best to use 500 or more.
Eight, brush one. After the walls of the floating dust are clean, you can paint the wall paint for the first time (the first pass can be diluted, and the second and third passes are slightly thicker).
Nine, find supplements. Strong light obliquely, looking for compensation and secondary polishing. Looks good on the wall, once brushed over the wall paint, small flaws immediately revealed no doubt, so must be brushed again, after the second seeking repair, polished, in order to have good results.
Ten, brush two. After the inspection, paint the second and third coats of the wall paint.
Note:
First, gypsum powder and 801 must use high quality materials. Like me, I only use "Hongxu" gypsum powder and "Suizhong" 801 rubber and white latex.
Second, fossil powder and putty powder are better or worse? Answer: putty powder. There is a situation that allows oil workers to adjust their own - after the house is decorated, let the special stay for ten years. understand? !
Third, according to the specification, the wall paint should all be brushed three times, two times is very informal.
Four, when calculating the area, do not use too complicated way to convert. Multiplying the building area by two is almost the same. Do not make it too complicated. When looking for oil workers, let special report area, naturally know whether it is real.
Fifth, with the actual painting area, you can calculate the amount of their own. The amount of putty powder per square meter is basically about 2.5 kilograms; the actual brushing area per liter of wall paint is 5-7 square meters. Do not be misled by the sales staff of the store. Specialists calculate the theoretical value (significantly different from the construction value).
Six, putty powder is a general term (including ordinary putty and gypsum putty). And what we usually call putty powder does not include gypsum powder. Gypsum powder is generally used as a local leveling, putty powder is a large area of ​​scraping, but the putty is more than a certain thickness, there may be cracking, so you need to apply a thicker place, only gypsum powder, and gypsum powder must use 801 Or white latex to prepare, putty powder with tap water can be.
Three trees paint entrance decoration paint house heating window latex paint
Temperature Sensor,Thermocouple Thermometer,Temperature Monitor,Temperature Instruments
Wuxi Winsun Automation Instrument Co., Ltd , https://www.winsunwx.com