Bearing device and disassembly method

Source: China Bearing Network Time: 2018-02-20

/*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089';

The device of the bearing and the device for disassembling the bearing, the method of disassembling; it should be determined according to the layout of the bearing, the size of the bearing and the cooperation with the bearing components. The pressure of the device and disassembly should be directly added to the end face of the tightly cooperating ring. Can not pass the pressure through the rolling body; as this will form an indentation on the bearing work; affect the normal operation of the bearing; and even damage the bearing. The bearing frame, seal ring, dust cover and other parts are very simple deformation; device or dismantle The pressure of the open bearing cannot be added to these parts.
(1) The inner ring of the bearing and the shaft are tightly cooperated; the outer ring and the casing are loosely cooperative; the bearing can be press-fitted on the bearing by the press; then the shaft is loaded into the casing together with the bearing; A bearing sleeve (copper or soft steel pipe) of a soft metal material is placed on the end face of the bearing. The inner diameter of the casing of the device should be slightly larger than the diameter of the journal; the outer diameter should be smaller than the diameter of the rib of the inner diameter of the bearing; A large number of device bearings can be added to the sleeve on the handle.
The bearing device should make the bearing hole and the center line of the shaft coincide. The bearing is not only difficult to be tilted relative to the shaft; and the indentation, the journal bending and the inner ring of the bearing will be cracked.
In the local area where the press is short or unable to use; the bearing sleeve and the small hammer device bearing can be used. The hammering force should be evenly transmitted to the entire circumference of the end face of the bearing ring; therefore, the end face of the device casing subjected to hammering should be made. spherical.
(2) The bearing outer ring and the housing hole are tightly cooperated; the inner ring and the shaft are loosely coupled; the bearing can be pressed into the housing first; at this time, the outer diameter of the device sleeve should be slightly smaller than the diameter of the housing hole.
(3) bearing inner ring and shaft; the outer ring and the housing hole are tightly cooperated; the end face of the device sleeve should be made into a ring that can press the end surface of the inner ring of the bearing together; or use a disc and device sleeve; The pressure is transmitted to the inner and outer rings together; the bearing is pressed into the shaft and the housing. This device method is uniquely applicable to the device for the active spherical centering spherical bearing.
(4) Heating device; the force required for the bearing of the device is related to the bearing scale and the size of the cooperative interference; the method of hot charging for medium and large bearings with large interference is required. The bearing ring is evenly heated to 80~100 Â°C in the fuel tank or special heater (not to exceed 100 Â°C).
Hot-mounted bearings require skilled operation skills. When the bearings are removed from the heating tank or the heater; immediately clean the oil and the attached objects with a clean cloth (not cotton yarn); Front; push the bearing to the position of the shoulder in one operation. It should be pushed all the way during the cooling process; or use a small hammer to tap the bearing through the device casing to make it tight. When the device is slightly rotated, the bearing should be slightly rotated; In case the device is skewed or stuck.
When the bearing outer ring and the housing hole are tightly cooperated, the housing can be heated and then loaded into the bearing. The unique bearing seat made of light metal is in tight cooperation; the bearing outer ring can be damaged by the bearing outer ring; The bearing housing should be heated.

Recommend to friends comments close window

Bearing related knowledge

The production process of yaw bearings discusses the basic way of bearing failure. The description of bearing speed limit Several common classification methods of rolling bearings
Difference between additional dynamic load and additional static load of SKF bearing

This article links to http://
Please indicate the bearing network http://

Previous:NTN/NSK Single Row Angular Touch Bearing Next:Analysis of the Variety Analysis of Bearings

Description of Protective Face Shield

Our company is the china leading manufacturers and suppliers of the protective Face Shield,with the very competitive price and good quality control, the protective face shiled is mad of PET material, it can protect people from gas, virus, water and so on, the face shield has CE/FDA certificate.

For the packing of protective face shield is 200pcs/carton, carton size is 54x35x46cm

Photo of the disposable face shield

Face Shield

Medical Protective Face Shield,Protective Face Shield,Plastic Protective Face Shield,Face Shield Visor

Dongguan Smart Furniture Co.,Ltd , https://www.smtfurniture.com